specification model dc voltage rated current rated power output voltage adj. range note.6 current adj. range line regulation load regulation setup, rise time note.8 hold up time (typ.) voltage range note.5 frequency range power factor (typ.) efficiency (typ.) ac current (typ.) input inrush current ( .) typ leakage current safety standards note.7 working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current note.4 over voltage over temperature can be adjusted by internal potentiometer or through output cable 2000ms, 80ms / 115vac 000ms, 80ms / 230vac at full load ; b type 2000ms, 200ms at 95 % load 230vac / 115vac at full load 1 16ms at full load 230vac /115vac 90 ~ 305vac 127 ~ 431vdc 47 ~ 63hz pf>0.96/115vac, pf>0.96/230vac, pf>0.94/277vac at full load (pl ease refer to "power factor characteristic" curve) 0.85a / 115vac 0.425a / 230vac 0.4a / 277vac cold start 70a/230vac <0.75ma / 277vac 95 ~ 108% protection type : constant current limiting, recovers automatical ly after fault condition is removed compliance to en55015, en61000-3-2 class c ( 60% load) ; en61000-3-3 compliance to en61000-4-2,3,4,5,6,8,11, en61547, en55024, lig ht industry level (surge 4kv), criteria a 20 ~ 95% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 60 ) 10 ~ 500hz, 5g 12min./1cycle, period for 72min. each along x, y, z axes ul8750, csa c22.2 no. 250.0-08(except for hlg-80h-48/54v & hlg-80h -48/54bl), ul8750 listed for hlg-80h- bl en61347-1, en61347-2-13 independent approved ; design refer to ul6 0950-1, tuv en60950-1 , j61347-1, j61347-2-13, ip65 or ip67 357.8khrs min. mil-hdbk-217f (25 ) 195.6*61.5*38.8mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. constant current operation region is within 60% ~100% rated output vol tage. this is the suitable operation region for led related application s, but please reconfirm special electrical requirements for some specific syste m design. 5. derating may be needed under low input voltages. please check the static c haracteristics for more details. 6. type a only. 7. safety and emc design refer to en60598-1, cns15233, gb7000.1, fcc part 18. 8. length of set up time is measured at cold first start. turning on/off the powe r supply may lead to increase of the set up time. 9. the power supply is considered as a component that will be operated in combi nation with final equipment. since emc performance will be affected by th e complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 10. refer to warranty statement. 0.84kg; 16pcs/14.4kg/0.54cuft protection type : shut down o/p voltage, re-power on to recover 80w single output switching power supply universal ac input / full range (up to 305vac)built-in active pfc function protections: short circuit / over current / over voltage / over temperature cooling by free air convection ocp point adjustable through output cable or internal potentiometer ip67 / ip65 design for indoor or outdoor installations three in one dimming function (1~10vdc or pwm signal or resistance) suitable for led lighting and moving sign applications compliance to worldwide safety regulations for lighting 5 years warranty (note.10) "ul8750 listed" safety approved for hlg-80h- blsuitable for dry / damp / wet locations class 2 power unit features : h l g - 8 0 h s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment safety & emc protection 85 10 (rth2) protection type : shut down o/p voltage, re-power on to recover blank : ip67 rated. cable for i/o connection. 14 ~ 17v 59 ~ 68v 88% 89% 90% 90.5% 91% 91% 91% 91% 91% 2.5% 3 ~ 5a 2.0% 3 ~ 5a 1.0% 2.4 ~ 4a 1.0% 2.04 ~ 3.4a 1.0% 1.62 ~ 2.7a 1.0% 1.38 ~ 2.3a 1.0% 1.02 ~ 1.7a 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 2.0% 1.5% 1.0% 0.5% 0.5% 0.5% 0.5% 1.0% 0.9 ~ 1.5a 0.5% 0.5% 1.0% 1.17 ~ 1.95a 0.5% 0.5% 12v hlg-80h-12 hlg-80h-15 hlg-80h-20 hlg-80h-24 hlg-80h-30 h lg-80h-36 hlg-80h-42 hlg-80h-48 hlg-80h-54 7.2 ~12v 15v 9 ~ 15v 20v 12 ~ 20v 24v 14.4 ~ 24v 30v 18 ~ 30v 36v 21.6 ~ 36v 48v 28.8 ~ 48v 5a 5a 4a 3.4a 2.7a 2.3a 1.7a 60w 75w 80w 81.6w 81w 82.8w 81.6w 150mvp-p 150mvp-p 13.5 ~ 17v 150mvp-p 17 ~ 22v 150mvp-p 22 ~ 27v 200mvp-p 27 ~ 33v 200mvp-p 33 ~ 40v 200mvp-p 43 ~ 53v 10.8 ~ 13.5v 54v 32.4 ~ 54v 1.5a 81w 200mvp-p 49 ~ 58v 42v 25.2 ~ 42v 1.95a 81.9w 200mvp-p 38 ~ 46v withstand voltage isolation resistance i/p-o/p:3.75kvac i/p-fg:1.88kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh constant current region note.4 hlg-80h-12 a a : ip65 rated. output voltage and constant current level can be adjusted thr ough internal potentiometer. b : ip67 rated. constant current level adjustable through output cable w ith 1~10vdc or 10v pwm signal or resistance. bl : (option) contact mean well for details. d (option) : ip67 rated. timer dimming function, contact mean well for deta ils. -40 ~ +70 (refer to "derating curve") emc immunity emc emission short circuit hiccup mode, recovers automatically after fault condition is remove d selv ip65 ip67 f m m 110 (for hlg-80h-12~42bl only) (for hlg-80h-48/54bl only) (for hlg-80h-48/54 only) (except for bl type) (except for hlg-80h-48/54) (except for hlg-80h-48/54bl) 18 ~ 24v 23 ~ 30v 28 ~ 35v 35 ~ 43v 41 ~ 49v 54 ~ 63v 48 ~ 58v
mechanical specification case no.997a unit:mm ip67 rated. cable for i/o connection. 300 20 fg (green/yellow) svt 18awg 2c svt 18awg 2c 38.8 sjtw 18awg 3c 195.6 171.8 ac/l(brown) ac/n(blue) 12 9.6 4.2 4pl 300 20 +v(red) -v(black) ip65 rated. output voltage and constant current level can be adjusted thr ough internal (can access by removing the rubber stopper on the case.) potentiometer. 300 20 fg (green/yellow) 38.8 sjtw 18awg 3c 195.6 171.8 ac/l(brown) ac/n(blue) 12 9.6 4.2 4pl 300 20 +v(red) -v(black) io adj. vo adj. 61.5 61.5 46.5 46.5 32 32 85.9 85.9 t case t case 30.75 30.75 t case: max. case temperature. t case: max. case temperature. 300 20 fg (green/yellow) 38.8 sjtw 18awg 3c 195.6 171.8 ac/l(brown) ac/n(blue) 12 9.6 61.5 46.5 32 -v(black) +v(red) dim-(white) dim+(blue) 4.2 4pl 300 20 svt 18awg 2c ul2517 18awg 2c 85.9 t case 30.75 t case: max. case temperature. b type:(hlg-80h-_b) 80w single output switching power supply h l g - 8 0 h s e r i e s a type:(hlg-80h-_a) blank:(hlg-80h) file name:hlg-80h-spec 2012-02-21
230vac input only ip67 rated. timer dimming function, contact mean well for details. 300 20 fg (green/yellow) svt 18awg 2c 38.8 sjtw 18awg 3c 195.6 171.8 ac/l(brown) ac/n(blue) 12 9.6 4.2 4pl 300 20 +v(red) -v(black) 61.5 46.5 32 85.9 t case 30.75 t case: max. case temperature. 80w single output switching power supply h l g - 8 0 h s e r i e s d type(option):(hlg-80h-_d) file name:hlg-80h-spec 2012-02-21 dim+ (b type) dim- fosc : 100khz detection pwm & pfc circuit o.l.p. o.t.p. emi filter rectifiers power switching filter & rectifiers +v -v i/p fg control o.v.p. & o.l.p. pfc circuit block diagram derating curve static characteristics ambient temperature ( ) load (%) -40 -25 0 -10 15 30 50 60 70 20 40 60 80 100 input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 305 100 90 80 70 60 50 40 load (%) (horizontal)
64 68 72 76 80 84 88 92 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277vac 230vac 115vac 0 .7 8 0 .8 0 0 .8 2 0 .8 4 0 .8 6 0 .8 8 0 .9 0 0 .9 2 0 .9 4 0 .9 6 0 .9 8 1 .0 0 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % 2 7 7 v a c 2 3 0 v a c 1 1 5 v a c hlg-80h series possess superior working efficiency that up to 91% can be re ached in field applications. load efficiency (%) (80w) constant current mode there are two major kinds of led drive method "direct drive" and "with led driv er". a typical led power supply may either work in "constant voltage mode (cv) or c onstant current mode (cc)" to drive the leds. mean well's led power supply with cv+ cc characteristic can b e operated at both cv mode [with led driver, at area (a)] and cc mode [direct drive, at area (b)]. driving methods of led module typical led power supply i-v curve vo(%) 100 60 50 100 (max.) io (%) constant voltage area constant current area hiccup protection (a) (b) (c) 80w single output switching power supply h l g - 8 0 h s e r i e s file name:hlg-80h-spec 2012-02-21 power factor characteristic efficiency vs load (48v model) pf load
dimming connection diagram for turning the lighting fixture on/off : using a switch and relay can turn on/off the lighting fixture. using the built-in dimming function on b-type model can't turn the lighti ng fixture totally dark. please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the led power s upply unit. 1.output constant current level can be adjusted through output cable by c onnecting a or 1~10vdc or 10v pwm signal between dim+ and dim-. resistance 2.the led lighting fixture can be turned on/off by the switch. hlg-80h dimming operation reference resistance value for output current adjustment (typical ) built-in 3 in 1 dimming function, ip67 rated. output constant current lev el can be adjusted through output cable by connecting a resistance or 1 ~ 10vdc or 10v pwm signal between dim+ and dim-. please do not connect "dim-" to "-v". fg (green/yellow) ac/l(brown) ac/n(blue) -v(black) +v(red) dim-(white) dim+(blue) n fg l relay blue brown green/ yellow ac/l ac/n hlg-80h b type dim+ dim- v(-) v(+) blue white black red switch adjuster 0~100k ohms resistance 1~10v dc voltage 10v pwm signal led lighting fixture 80w single output switching power supply h l g - 8 0 h s e r i e s file name:hlg-80h-spec 2012-02-21 60k 60% 60% 10k 10k /n 20k /n 30k /n 40k /n 50k /n 60k /n 70k /n 80k /n 90k /n 100k /n single driver multiple drivers (n=driver quantity for synchronized dimming operation) 1v 4v 7v 2v 5v 8v 3v 6v 9v 10v 10% 10% 20k 20% 20% 30k 30% 30% 40k 40% 40% 50k 50% 50% 70k 70% 70% 80k 80% 80% 90k 100k open open open 90% 90% 100% 100% resistance value dimming value percentage of rated current percentage of rated current 1 ~ 10v dimming function for output current adjustment (typical) 60% 60% 10% 10% 20% 20% 30% 30% 40% 40% 50% 50% 70% 70% 80% 80% 90% 90% 100% 100% duty value percentage of rated current 102%~108% ----- 102%~108% 102%~108% 10v pwm signal for output current adjustment (typical): frequency ra nge :100hz ~ 3khz
waterproof connector waterproof connector can be assembled on the output cable of hlg-80h to ope rate in dry/wet/damp or outdoor environment. hlg-80h i/p o/p led lamp ac source cable joiner junction box(option ) pin configuration (female) pin configuration (female) size size m12 m15 4-pin 5a/pin m12-04 order no. order no. 10a max. suitable current suitable current 5-pin 5a/pin m12-05 10a max. 2-pin 12a/pin m15-02 12a max. up to four wires can be connected through this cable joiner bysoldering or clamping by tools. 66 26 20 25 cj04-2 suitable for 18awg~22awg cj04-1 suitable for 14awg~16awg o/p wires led lamp hlg-80h waterproof connection cj04 cable joiner can be purchased independently for user's own assembl y. optional junction box available for , please contact meaw well for deta ils. a / blank - type hlg-80h- bl models with junction box at both input and output side are liste d. mean well order no. : cj04-1, cj04-2. svt 18awg 2c fg (green/yellow) 38.8 35 sjtw 18awg 3c ac/l(brown) ac/n(blue) 61.5 171.8 334 150 20 -v(black) +v(red) 150 20 3- pf 1/2" 61 32 8.5 8.5 3- pf 1/2" 86 76 5 10 6 2- 5 80w single output switching power supply h l g - 8 0 h s e r i e s file name:hlg-80h-spec 2012-02-21
|
